LittleFS Flash File System

LittleFS Flash File System

I recently learned about a compact embedded Flash File System known as SpiFFS.
While researching SpiFFS, I soon learned of another compact embedded Flash File System, LittleFS.
LittleFS appears to be even more compact and has additional security in that it creates and maintains a CRC for each file, and verifies the CRC each time the file is read.

• Compact
• Power-loss resilience
• Dynamic wear leveling
• Bounded RAM/ROM
• Maintains revision count and CRC (security features)

The Hardware

Let's put this file system onto an STM32 board and check it out.

I'll be using a NUCLEO-F103RB ($10.34), with a Winbond W25Q128FVSG SPI Flash module from Ebay.
https://www.ebay.com/itm/264290947181  If the link doesn't work, just search Ebay for "W25Q128 Module".
I bought two for $8.26 (free shipping).  Download the PDF for the W25Q128FVSG:
https://www.winbond.com/resource-files/w25q128fv%20rev.m%2005132016%20kms.pdf

The W25Q128FVSG uses 2.7V to 3.6V for operation. Here's a diagram for the the chip's pins and signals,
along with the Ebay "W25QXX" module" photo:

Since the NUCLEO-F103RB powers its STM32F103RB processor with 3.3V, this "W25QXX" module"
is compatible with the NUCLEO-F103RB.  (The STM32-F103RB is capable of running from 2.0V to 3.6V.)

Let's look at the signal pins on the NUCLEO-F103RB:

On the NUCLEO board, the SPI1_SCK signal is being used to drive the board's Green LED.
So, we will use SPI2 bus and its signal pins.
To connect up the signals for power and the SPI BUS, here's the wiring diagram that was used:
Winbond W25Q128FVSG SPI Flash Module wiring:

        W25QXX  Windbond
Signal    Pin     Pin   Color    NUCLEO-F103RB Signal & Pin
  DI       1       5    Brown    PB15 SPI2_MOSI  CN10-26
  CLK      2       6    Red      PB13 SPI2_SCK   CN10-30
  GND      3       4    Orange   GND             CN10-20
  DO       4       2    Yellow   PB14 SPI2_MISO  CN10-28
  CS       5       1    Green    PB12 SPI2_NCS   CN10-16
  VCC      6       8    Blue     +3V3             CN7-16

The Software

The SPI and Serial Interface

Let's start by getting enough in place to read the Manufacturer and Device ID from the Winbond part.
Within the STM32CubeIDE configuration for your project:
* Enable SPI2 as "Full-Duplex Master".,  
* Hardware NSS Signal: "Disable"  - We will use GPIO control for this signal.
  - Don't bother trying to use some form of SPI hardware control for this signal pin.
* Frame Format - Motorola, 8-Bits, MSB First
* Clock Prescaler 256,  (140,625KBits/s - Using 72MHz SYSCLK - this can be changed later)
* Clock Polarity - CPOL: Low (signal is normally low)
* Clock Phase - CPHA: 1 Edge (first rising edge)
* CRC Calculation: Disabled
* NSS Signal Type: Software (GPIO control)
* Select PB12 Pin, change signal to GPIO_Output, name it "SPI2_NCS"
  Click on Pinout & Configuration tab -> System Core -> GPIO -> PB12 - Set GPIO output to "High"
  We want the SPI2_NCS signal high - inactive initially.
* Configure the HCLK for 72MHz (this is rather optional).
    (The Winbond part will function well beyond what this STM32 processor can clock over the SPI bus)
Optional configuration and code that will ease debugging
Select and configure USART2 (The USART2 signals are routed to the NEUCLEO's ST-LINK chip,
    creating a serial connection to your host computer over USB.)
* Mode: Asychronous, Hardware Flow Control (RS232): Disable
* Baud Rate: 115200, 8 bits, No Parity, 1 Stop Bit, Data Direction: Receive and Transmit

Serial Output, Serial Input, and printf() Support

See: https://merkles.com/wiki/index.php/Getting_Started_with_STM32#Create_a_New_STM32CubeIDE_1.10.1_Project_-_Hello-World

The Winbond 25Q128 (128M-Bit) Library

Here's my example of a STM32 HAL interface to the Winbond W25Q128 part:
w25q128.c
w25q128.h

Debugging LittleFS

Capture and check the return code from all function calls. The original example didn't do this.

* Check the return code for lfs_mount().  Make sure it retuns LFS_ERR_OK.
  - Although, the first time, it will return an error, and require an lfs_format() call.
* Check the return code for lfs_file_open().  Make sure it retuns LFS_ERR_OK.
* Although I didn't check the return code for lfs_file_rewind(), lfs_file_write(), and lfs_file_close(),
  it wouldn't hurt.
* There are plenty of debug printf()s in the code already.  Just need to enable them.
  Open up lfs_util.h, around line 50, you will want to define LFS_YES_TRACE, to enable printf() tracing:
#define LFS_YES_TRACE
// Logging functions
#ifdef LFS_YES_TRACE}}
* If your terminal wants CR/LF pairs, edit the printf() strings, adding "\r" to go with the "\n" line feed character.

To Do

Using the command line interface, test the SPI interface with the W25Q128.
1) Begin with the JEDIC ID command.  Display the part's ID: 
 See: cl_w25_id() in w25q128.c
    >w25id
    Jedec ID: 0xEF 0x40 0x18

2) This part has a unique ID assigned to it.  Display it:
 See: cl_w25_unique_id() in w25q128.c
    >w25uid
    Unique ID: D2 65 CC 22 67 24 37 28   <This ID is from one of my parts.  Yours will be different.>

At this point, you have both written to and read from the SPI FLASH device.
If your ID is correct and you're not getting errors, chances are your SPI interface is functioning well.
You can test erasing, reading, and writing to the FLASH device, and if you have an logic analyzer or
digital scope, you can validate the resulting timing with the FLASH chip's data sheet.

Reference / Additional Information

https://uimeter.com/2018-04-12-Try-LittleFS-on-STM32-and-SPI-Flash/
https://github.com/ARMmbed/littlefs
https://github.com/ARMmbed/littlefs/blob/master/README.md