ST7735S 80x160 0.96" SPI LCD Display Module: Difference between revisions
Jump to navigation
Jump to search
(Created page with "==ST7735S 80x160 0.96" SPI LCD Display Module== '''Hardware''' right|thumb right|thumb These displays use the ST7735S cont...") |
No edit summary |
||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
==ST7735S 80x160 0.96" SPI LCD Display Module== | ==ST7735S 80x160 0.96" SPI LCD Display Module== | ||
===Hardware=== | |||
[[File:80x160_front.jpg|right|thumb]] | [[File:80x160_front.jpg|right|thumb]] | ||
[[File:80x160 back.jpg|right|thumb]] | [[File:80x160 back.jpg|right|thumb]] | ||
| Line 19: | Line 19: | ||
BLK ???? (This can remain unconnected.) | BLK ???? (This can remain unconnected.) | ||
'''Notes:''' | '''Hardware Notes:''' | ||
* | * The wire colors shown above are messed up. The harness was pulled off of another SPI display. | ||
* The | ===Software=== | ||
Installed '''"Adafruit_ST7735_and_ST7789_Library", version 1.6.0.''' | |||
Using Arduino/libraries/Adafruit_ST7735_andST7789_Library/examples/graphicstest/graphicstest.ino example | |||
Modified to use the following constructor: | |||
// For 1.44" and 1.8" TFT with ST7735 use: | |||
Adafruit_ST7735 tft = Adafruit_ST7735(TFT_CS, TFT_DC, TFT_RST); // Using this for Hardware SPI | |||
Modified to use the following display initialization: | |||
// OR use this initializer (uncomment) if using a 0.96" 160x80 TFT: | |||
tft.initR(INITR_MINI160x80); // Init ST7735S mini display | |||
'''Software Notes:''' | |||
* The display colors are messed up. | |||
ST77XX_RED displays as blue. | |||
ST77XX_YELLOW displays as light blue. | |||
* Occasionally, a messed up row is visible on the bottom of the display, | |||
and a messed up column is visible on the right side of the display. | |||
Latest revision as of 17:12, 12 January 2021
ST7735S 80x160 0.96" SPI LCD Display Module
Hardware
These displays use the ST7735S controller: https://www.crystalfontz.com/controllers/Sitronix/ST7735S/320
Connecting to the Arduino Uno as follows:
LCD Wire Signal Color UNO Pin GND Red GND VCC Brown 5V LED Grey 3.3V (or 200 ohm resistor to 5V) SCL Violet 13 SCLK SDA Blue 11 MOSI RES Yellow 9 DC Green 8 (This is the Data/Command DC signal) CS Orange 10 BLK ???? (This can remain unconnected.) Hardware Notes: * The wire colors shown above are messed up. The harness was pulled off of another SPI display.
Software
Installed "Adafruit_ST7735_and_ST7789_Library", version 1.6.0.
Using Arduino/libraries/Adafruit_ST7735_andST7789_Library/examples/graphicstest/graphicstest.ino example
Modified to use the following constructor:
// For 1.44" and 1.8" TFT with ST7735 use:
Adafruit_ST7735 tft = Adafruit_ST7735(TFT_CS, TFT_DC, TFT_RST); // Using this for Hardware SPI
Modified to use the following display initialization:
// OR use this initializer (uncomment) if using a 0.96" 160x80 TFT:
tft.initR(INITR_MINI160x80); // Init ST7735S mini display
Software Notes:
* The display colors are messed up.
ST77XX_RED displays as blue.
ST77XX_YELLOW displays as light blue.
* Occasionally, a messed up row is visible on the bottom of the display,
and a messed up column is visible on the right side of the display.