NUCLEO-G071RB
In December, 2018, STMicro announced their STM32G0 - value line of microcontrollers. https://blog.st.com/stm32g0-mainstream-90-nm-mcu/
The NUCLEO-G071RB is STMicro's low cost development board for the STM32G071RBT6 processor. This board is often used as a training tool for the STM32G0 series devices.
Data Brief for NUCLEO-G071RB: https://www.st.com/resource/en/data_brief/nucleo-g071rb.pdf
Data Brief for STM32G071RB: https://www.st.com/en/microcontrollers-microprocessors/stm32g071rb.html
NUCLEO-G07RB Schematic: https://www.st.com/resource/en/schematic_pack/mb1360-g071rb-c01_schematic.pdf
STM32G0 Getting started - hardware development document:
https://www.st.com/resource/en/application_note/dm00443870-getting-started-with-stm32g0-series-hardware-development-stmicroelectronics.pdf
Firmware: https://www.st.com/en/embedded-software/stm32cubeg0.html
ST Website for the STM32G0 family: http://www.st.com/stm32g0
Product overview document, 117 pages: https://www.st.com/resource/en/datasheet/STM32G071RB.pdf
- Arm® Cortex®-M0+ 32-bit MCU
- 128 KB Flash
- 36 KB RAM
- 1.7-3.6V
- Up to 64MHz clock
- 32.768K crystal
- 4x USART, 14 timers, 2 - 12bit DACs, 2 I2C, 2 SPI (32Mbit/sec)
- 12-bit, 0.4 μs ADC (up to 16 ext. channels)
- 24MHz clock from STLink via MCO signal into PF0, pin 10 (Morpho CN7-29) - requires SB17 install
- Green LED, LD4, connects to PA5, active high (D13 on Arduino connector)
- Blue push-button, B1, connects to PC13, pin 3. Shorts to ground when pressed.
- USART2 connects to STLink for Serial to USB function
RM0444, STM32G0x1 advanced Arm®-based 32-bit MCUs, 1230 pages:
https://www.st.com/resource/en/reference_manual/dm00371828-stm32g0x1-advanced-armbased-32bit-mcus-stmicroelectronics.pdf
STM32G0 Online Training:
https://www.st.com/content/st_com/en/support/learning/stm32-education/stm32-online-training/stm32g0-online-training.html
Software Tools
- STM32G0 - STM32CubeMX: https://st-onlinetraining.s3.amazonaws.com/STM32G0-Ecosystem_CubeMX_Tool/index.html
- STM32Cube G0 firmware package: https://st-onlinetraining.s3.amazonaws.com/STM32G0_Ecosystem_Firmware_drivers-%28FW%29/index.html
- https://www.st.com/en/embedded-software/stm32cube-mcu-mpu-packages.html
Keil MDK Keil Pack installer: https://www.keil.com/dd2/st/stm32g031j6mx
Everything compiled and built well.
{{#if:|{{#ifexpr:({{#time:U|{{{3}}}}} - {{#time:U|now}}) > 0|I had a problem downloading: "Flash Download failed - Cortex - M0"
|I had a problem downloading: "Flash Download failed - Cortex - M0"
}}|I had a problem downloading: "Flash Download failed - Cortex - M0"
}}
The issue is the lack of a programming method defined.
Project -> Options for Target xxx (Alt F7) -> Debug tab -> Use ST-Link Debugger -> Settings -> Flash Download ->
Add the STM32G0xx 32KB Flash algorithm with Address Range 080000000H - 08007FFFH.
Additional Websites / Notes:
http://www2.keil.com/stmicroelectronics-stm32/mdk